ANALISA NUMERIK PERILAKU PENAMPANG BAJA CANAI DINGIN UNLIPPED CHANNEL AKIBAT BEBAN AKSIAL
DOI:
https://doi.org/10.51988/jtsc.v4i1.119Keywords:
Cold-formed steel, unlipped channel, finite element method, SNI 7971-2013, ABAQUSAbstract
The development of construction material that is more efficient and friendly continued by researchers. Steel is a material that is widely used in construction, especially hot-rolled steel, the use of cold-formed steel is an innovation where cold-formed steel has more advantages than hot-rolled steel. Many studies of cold-formed steel sections due to applied loads have been carried out to observe the behavior and capacity of the sections. An unlipped channel is a steel section that can be used in buildings, cold-formed steel unlipped channel will be subjected to an axial load to see the behavior and capacity of the section which is the aim of this study. In this study, a numerical analysis of cold-formed steel sections will be performed using the finite element method through ABAQUS software, the numerical analysis is committed based on existing research in the literature. The Sectional capacity resulting from the numerical analysis will be compared with the effective width method approach based on SNI 7971-2013.
References
Ananthi, G. B. G., Vishuvardhan, S., & Knight, G. M. S. (2015). Experimental, theoretical and numerical study on thin walled steel single and compound channel sections in axial compression. Indian Journal of Engineering & Materials Sciences, 22, 570–580. https://www.researchgate.net/publication/287808905
Budiman. (2022). Buckling Analysis of Skew Plates Subjected to Uniform Compression Loading. International Journal of Civil Engineering and Infrastructure, 2(1), 1–9.
Hancock, G. J. (2007). Design of cold-formed steel structures?: to Australian/New Zealand standard AS/NZS 4600:2005 (4th ed., Vol. 4). Australian Steel Institute.
Janarthanan, B., & Mahendran, M. (2020). Numerical study of cold-formed steel channel sections under combined web crippling and bending action. Thin-Walled Structures, 152. https://doi.org/10.1016/j.tws.2020.106766
Janarthanan, B., & Mahendran, M. (2021). Behaviour and strength of unlipped channel sections under combined bending and torsion. Journal of Constructional Steel Research, 182. https://doi.org/10.1016/j.jcsr.2021.106648
Peiris, M., & Mahendran, M. (2021). Behaviour of cold-formed steel lipped channel sections subject to eccentric axial compression. Journal of Constructional Steel Research, 184. https://doi.org/10.1016/j.jcsr.2021.106808
Peiris, M., & Mahendran, M. (2022). Advanced numerical modelling of light-gauge steel framed walls subject to eccentric compression. Engineering Structures, 256. https://doi.org/10.1016/j.engstruct.2022.114063
Schafer, B. W., & Peköz, T. (1998). Computational modeling of cold-formed steel: characterizing geometric imperfections and residual stresses. Journal of Constructional Steel Research, 47, 193–210.
Standard Nasional Indonesia. (2013). Struktur Baja Canai Dingin. www.bsn.go.id
Standards Australia (SA), & AS/NZS 4600. (2005). Cold-Formed Steel Structures. Standards Australia.
Yu, W.-W., & Laboube, R. A. (2010). Cold-Formed Steel Design (Fourth Edition, Vol. 4). John Wiley & Sons, Inc.
Janizar, S., Setiawan, F., & Saputra, D. H. (2020). AUDIT STRUKTUR GEDUNG BANK X KOTA BANJARMASIN. JURNAL TEKNIK SIPIL CENDEKIA (JTSC), 1(1), 15-26.
Hafudiansyah, E., & Anisarida, A. A. (2021). ANALISIS STRUKTUR MOORING DOLPHIN KAPASITAS KAPAL 2000 GT (STUDI KASUS PELABUHAN MUNSE SULAWESI TENGGARA). JURNAL TEKNIK SIPIL CENDEKIA (JTSC), 2(1), 69-83.
Rahmanto, T., & Janizar, S. (2022). PENGENDALIAN BIAYA DAN WAKTU DENGAN METODE EARNED VALUE PROYEK FAMILIA URBAN BEKASI. JURNAL TEKNIK SIPIL CENDEKIA (JTSC), 3(2), 16-27.
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Jurnal Teknik Sipil Cendekia (JTSC)
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
